ITG 01-114 Drawing
Tractors & Equipment Online Monthly Specials
Contact: Dawson Jones, Inc. 937-242-6637 or dawson@tractors-equipment.com
TE Parts Crib Monthly Specials, Page 2
ITG 01-114 / OMNI RC61
The 01-114 / RC61 Gear box is rated from 75hp to 90hp. This box is commonly used on medium to heavy duty 5', and 6' cutters,
some 7' cutters, and 8' and 10' multiple gearbox cutters. Please see note below.

  1. It has a diamond shape mounting bolt pattern with 4 3/4" between bolt centers. (On this gear box one bolt hole is directly
    under the input shaft.)
  2. The input shaft is 1 3/8" 6 spline.
  3. The output shaft is 1.96" 15 spline
  4. The gear ration is 1:1.46 (19 teeth on the input shaft gear, 13 teeth on the output shaft gear)
01-114 / RC61
Note:
they must be matched in exact gear tooth count. On these boxes the blade arcs overlap. If they aren't the same,
the blades will strike
  • during the operation causing damage to the blades, boxes and the cutter itself.

  • If you have any questions at all regarding gearbox suitability, whether your existing box is conpatible with a
    new box, Please call us at 937-242-6637
ITG 01-034 Drawing
ITG 01-034 / Omni RC71
01-034 / ITG 75S / RC71
The 01-034 / ITG75S is generally rated at over 100hp and is used on many Heavy Duty applications. Everything about this box is built for hard
work. This box is commonly used on HD6' and 7' cutters.

  1. It has a diamond shape 4 bolt mounting pattern with 4 3/4" between bolt centers. (On this gear box one bolt hole is directly under the
    input shaft.)
  2. The input shaft is 1 3/4" 20 Spline
  3. The output shaft is 1.96" 15 spline
  4. The gear ration is 1:1.46 (19 teeth on the input shaft gear, 13 teeth on the output shaft gear)
  5. This box is compatible with several Alamo Group boxes, especially Rhino.
More gearboxes to come, just hold on!
DE19106A-Kit
Replacement gear set for John Deere MX5, MX6, MX7, MX8, and MX10 mowers
including a new output shaft, new ring gear, input seal, output seal and rear
rubber cap.

These are a little dusty but brand new, never installed.

The gear on the shaft has 13 teeth, the ring gear has 22 teeth. 1:1.69 Ratio

Fits MX models with Iberica (Made In Spain) gearbox:
  • 13 tooth pinion with shaft, 15 splines at bottom of shaft for blade carrier
  • 22 tooth ring gear
  • New input seal
  • New output seal
  • New rubber cap for rear of gearbox

This gear set will fit in all of the MX boxes made in Spain.

The major difference between models is the gear ratios.
  • The MX7 has a ratio of 1:1.47. Gear teeth are 22 input and 15 output
  • The MX8 has a ratio of 1:1.47. Gear teeth are 22 input and 15 output
  • The MX10 has a ratio of 1:1.22. Gear teeth are 22 input and 18 output

With the MX8 and MX10 models you will need to order two sets and rebuild
both boxes.
Our customers don't see the lower ratios as being a problem, they merely slow
the PTO rpm's down a little.
75hp to 90hp Gear box
100 hp + Gear box
MX Gearbox (Made In Spain)
Rebuild Kit DE19106A Kit
Splitter Gearbox
250hp Splitter Box for Batwing Cutters
All Shafts are 1 3/4" 20 Spline,
Gearboxes are Suitable for 540 RPM or 1000 RPM
We sell this gearbox for use
on John Deere, Schulte,
Batwing mowers.

Be sure to check the
dimensions on the drawing to
insure a good fit or to know
what modifications are
needed to make it fit.

Comparable boxes will cost
half again or double.

Center shaft ratio is 1:1 Horse
Power 250

Input Shaft (A) 1 3/4" 20
Spline Output Shaft (B) 1 3/4"
20 Spline (X3)

1000RPM Ratio is 1.2:1,

540RPM Ratio is 1:1.21

This gearbox is shipped dry,
the buyer will have to add oil.
T25A / 540RPM  T25A / 1000RPM
The 540RPM Box is
$975.00
including S/H
The 1000RPM Box is
$849.00
Including S/H
$395.00 Includes S/H
$495.00 Includes S/H
$492.50 Includes S/H